鋼結構廠房如何施工，鋼結構廠房施工工藝:鋼結構廠房本身具有重量輕、強度高、抗壓能力強、施工周期短等特點。

How to construct a steel structure factory building and its construction technology: The steel structure factory building itself has the characteristics of light weight, high strength, strong compressive capacity, and short construction period.

鋼結構廠房具體施工工藝：

Specific construction technology for steel structure factory buildings:

1.鋼結構廠主要結構吊裝：地面拼接鋼梁、鋼柱架設、鋼梁吊裝、連接子結構、糾正主體結構偏差、安裝起重梁(可選)、吊裝夾層(可選)、涂防火涂料。

1. Main structural lifting in steel structure factory: ground splicing of steel beams, installation of steel columns, lifting of steel beams, connection of substructures, correction of main structural deviations, installation of lifting beams (optional), lifting of intermediate layers (optional), and application of fire-resistant coatings.

2.鋼結構廠房二次結構安裝：屋面墻檁條、屋面墻支撐、翼緣支撐等。

2. Secondary structure installation of steel structure factory building: roof wall purlins, roof wall supports, flange supports, etc.

3.鋼結構廠房屋面板及保溫層安裝：先鋪設保溫層，再安裝屋面板（部分工程仍在保溫層下鋪設鋼絲網，防止保溫層脫落，主要取決于保溫層等級）。屋頂主要是防水的。因此，有必要將廣告牌與木板重疊，釘板，膠水應滿但不滿意，膠水應清洗，板表面涂層不應損壞，防止腐蝕等。

3. Installation of Steel Structure Factory House Panel and Insulation Layer: First lay the insulation layer, then install the roof panel (some projects still lay steel wire mesh under the insulation layer to prevent the insulation layer from falling off, mainly depending on the insulation layer level). The roof is mainly waterproof. Therefore, it is necessary to overlap the billboard with the wooden board, nail the board, and ensure that the glue is full but not satisfactory. The glue should be cleaned, and the surface coating of the board should not be damaged to prevent corrosion.

4.鋼結構廠房自身墻體的維護安裝:主要安裝墻體保溫層和墻板。墻體主要是窗戶區域的美觀和防水。還有確定安裝是否有偏差的問題。比如底部要平整，整個平面要平整，板與板之間的平整度偏差要符合要求。

4. Maintenance and installation of the steel structure factory building's own walls: mainly installing wall insulation layer and wall panels. The wall mainly focuses on the aesthetics and waterproofing of the window area. There is also the issue of determining whether there is any deviation in the installation. For example, the bottom should be flat, the entire plane should be flat, and the flatness deviation between boards should meet the requirements.

5.鋼結構標準廠房細節結構:主要是一些裝修安裝，如屋面與墻面之間的角落、角落、墻板與磚墻之間的防水板、門窗裝飾等。細節結構是美容工程的一個環節，也是主要組成部分之一，所以水平、平面和垂直是基本的。

5. Steel structure standard factory building details: mainly for decoration and installation, such as corners and angles between roof and wall, waterproof boards between wall panels and brick walls, door and window decorations, etc. The detailed structure is a part and main component of beauty engineering, so horizontal, flat, and vertical are fundamental.